IVA – 26th JUNE 2018

It’s done, following the online application , which has now been approved and paid for … £450.00 (ouch) I now have a date set for the 26th JUNE 2018.

Nervous and excited all in one is the best way to explain it!

Next things to do, are to get a pre-MOT booked to test the various aspects, brakes and lights, emission etc and have a garage give it a proper look over.

oh Heck!

 

Advertisements

It’s done!

I took the week off work with the intension of getting the car ready for the IVA and I can finally say it’s done.

VIN plate is stamped and riveted to the car in the engine bay, I finished tidying up a few of the wires that I thought might be a little dodgy at the IVA by basically extending the conduit on some of them. The paper work is all done, forms all filled out, photos enclosed of the build … now sent!

All I can do now is wait for a test date! Once I receive that I’ll get the car down for an MOT to test the various aspects, brakes and lights etc.

More on this when I have news 🙂

Forgot to add, its all done online too, so scan everything and keep it all under 5MB

Last few bits

This is it, I’m almost at the finish line, just a few more bits to do. Enough chit chat today lets get straight into the next piece of work.

At some point you need to reinforce the tunnels fixing the chassis to the body, it helps with keeping it stable apparently. So with this in mind the manual says to use ply wood, however I decided because I love fibreglassing I would do that instead! First off I measured the gap, cut up and moulded some wire mesh to fit. Positioned this in the tunnel which was fairly fiddly and left my arms looking like I’d been attacked by a pack of hungry cats!

 

Anyway once the mesh was in and fixed I fibreglassed it in place, another very messy job and tricky with everything in the way but not impossible. Once Id’ built up enough layers of fibreglass I left it to go off and then painted it black with the same paint I used on the rest of the car (rear inner wings etc) just as another level of protection really. Once the inner front wheel arches are in you won’t even see that area.

OK, next item was something I found out about which is required for an IVA pass. It’s not in the manual anywhere so thankfully someone mentioned it otherwise that would have been very annoying! So what is it you ask, well, you have blank off the area in the passenger footwell next to the mini-heater so that in the event of a problem with the water pipes your passenger doesn’t get sprayed with hot water! Safety first

I asked the question at Pilgrim and had no response so I went online on the cobra forum and got my answer almost immediately! I have to say if you need to know anything, get stuck or have an issue, ask online. Theres some very knowledgeable people on there, always happy to help.

Right, back to the issue at hand. Firstly I made a cardboard template of what the shield needed to look like. Then (luckily) I had some aluminium left over which I cut up, moulded and made as my template. Once that was done, I covered it with black fabric, drilled the holed through to the chassis and bolted it in place … done!

 

Consider you won’t ever actually see this, its functional and fixed in place, all IVA ready … hang on … ALL IVA READY! Yes, well almost yes, I’m waiting on the VIN plate from Pilgrim but thats it. The car is done, the forms are filled in and I’m ready.

Other than this, all I have to sort with the car is to over come an overheating issue I’m currently having. Hopefully this won’t be to much of an issue but apparently its quite a usual one for the Sumo. I’ll keep you posted once I know more.

UPDATE

I was told to check several things, including the expansion tank, restrictor valve, water levels, ensure all the air is out of the system etc and that the fan is blowing in the correct direction! … Guess what, the fan wasn’t. Who knew you could wire it incorrectly. Swapping the wires over has seemed to have fixed the issue tho 🙂 It was running for a longer period at around 90deg as apposed to the other day when it went up to 120deg! … Problem solved!

Until then, I also managed to get the car out of the garage for a clean …

 

It’s been a while

I think the title says it all really.

With one thing or another the past year has flow by as has the time. But I’ve still had the car sat in the garage gathering dust which is really annoying (especially as summer is approaching again) BUT to be honest I went through what a lot of personal issues and something a lot of amateur builders go through and that just everything get on top of you and it feels like every little issue is a massive one.

Well after feeling so down for a while, I approached Pilgrim to ask for help getting the project finished. Sadly after 1 email they never got back to me, which is a shame. Either way you look at it, customer service should be paramount, in my view anyway! So I took to the UK Cobra forum and the guys on there were very helpful and encouraging, I even had one guy ‘Tony’ who was going to come down and help me. So thanks Tony for the offer but sadly Tony had a fall so it didn’t happen but I wish him a speedy recovery.

With all the encouragement and help from fellow owners and builders alike I decided to take a week off work and get it sorted myself. So there is a plus in all this, I get to finish my car!

OK … on to the build progress.

Quite a few issues to sort out, firstly I had a strong smell of fuel from the boot, which I was informed is quite normal. I had a quick look and noticed the top clip was pinching a little so it may not have had a 100% seal on the cap. Quick rotate, retighten and all was sorted. There were a few pieces of carpet that were coming unstuck too which I managed to re-stick, this time using a special glue spray we used to carpet the VW camper. I should have used this first! Worked so much better.

A few other places in the passenger and driver footwell needed some attention, more sticking the carpets down, easily done with the right glue!

Next step was to swap the front callipers over! Somehow, I managed to put them on the wrong side, so basically the bleed nipples were at the bottom. This turned out to be a easy job, couple of bolts and off they came, quick swap and done! While I had the front wheels off I decide to play a little with the camber of the wheels. I had to wait until the wife came home to re-bleed the brakes, but thats straight forward. I didn’t bother with pics here, because it all looks the same as before.

After this I had to fix a little problem the passenger front light. No idea what was happening here, everything else was working ok, but nothing from one head light. I checked all the fuses, all ok, took the light apart to check the bulbs hadn’t blown and that was ok, so lastly I opened up the conduit to find two of the cables had come apart!? Not sure how that happened but it did, so another quick fix. Once back together I crimped them to ensure a tight fit and placed them back in the conduit and taped it back up.

Then it came to sorting out my leak on the hydraulic clutch. I’ve had this very annoying leak in the footwell, where the clips I was using I just couldn’t get tight enough. I’d also noticed that the hose was touching one of the rocker covers so knowing the IVA is on the horizon I thought I would cut this shorter and re-route it. Pity I waited till now to do this as it made life difficult with everything in the way! However once done, theres now no leak and it looks neater and works better. I ended lifting the clutch reservoir up slightly (by about an inch) which also helped.

The other little job was to place a restrictor in the top hose from the radiator to the expansion tank. I did this before with a piece of plastic where I drilled a small hole through it, but I was never 100% happy with this. So I decided to redo this area by using some good plumbing materials. A flow restrictor with compression connections on to a piece of 2″ copper pipe, all connected and clips together (see picture above) This apparently helps the flow of water go through the radiator rather than through the expansion tank. Hopefully helping keep the engine temp down.

What else was there … oh yes, I had a slight wobble in the steering column so that was adjusted slightly, I also noticed I hadn’t quite tightened the bolts up as it joined the steering arm.

Last but not least! The HT leads were failing on the rocker covers, which from what I understand would be a failure, so I made up some quick brackets to keep them off for now. I’ll find a better solution, or at least one that looks better anyway later. For now, they are off the covers.

Oh I nearly forgot, I also managed to stamp the VIN number I received from the DVLA on the chassis. I used the lower part of the chassis, just in front of the wheel, drivers side to do this. There’s still the VIN plate to go inside the engine bay but I’m waiting for this to come from Pilgrim.

And that was it for the day, very happy with all the progress made. I still have the inner tunnels to fibreglass and seal off, and I need to redo the camber (I did it way to much) and I’m looking at shortening the amount of turning (lock to lock) the steering currently has as it is a fair bit. But I’ll see how it drives first.

So with that lot done, I’ll get on to the tunnels in the next few days, and then all I have left is the IVA to look forward to!